Comparative Strength Analysis of Concrete by Partial Replacement of Sand with Basic Oxygen Furnace Slag Musawir Quadir Department of Civil Engineering Surya World College of Engg. and Tech. Rajpura, INDIA ... A Guide to the Use of Iron and Steel Slag in Roads. Revision 2, (2002) Published by: Australasian Slag Association Inc. ...

SPLIT TENSILE STRENGTH. Tensile strength is defined as the topmost stress that a material can sustain while pulled or stretched. This test is conducted by replacing steel slag at a level of 10%, 20%, 30% and 40% after 7, 14, 28 and 50 days of curing for an M35 grade of concrete. Table

of waste iron as a partial replacement of sand in concrete., 2008. reuse of waste iron as a partial replacement of sand in concrete. waste management, vol. 28, pp., zz, alhashmi, eaof sand and pee be a supergreen replacement for concrete?, designers and scientists are experimenting with new materials that are structurally ...

on the replacement of natural sand with manufactured sand by 0%, 25%, 50%, 75%, and on concrete properties. The steel slag is one of the alternative materials that can be used instead of cement as a partial replacement in concrete by 0%. %, 5%, %, 10%, %, 15%.

observed that partial replacement of sand with copper slag has sound tensile and compressive stregth and it can be used as an additive in the conventional concrete. Partial replacement with copper slag also serves as a solution for the disposal of solid waste. .

properties of concrete containing copper slag as a partial replacement of fine aggregates in the concrete mix design. ... EXPERIMENTAL STUDY ON PROPERTIES OF STRENGTH AND DURABILITY OF CONCRETE BY PARTIAL REPLACEMENT OF FINE AGGREGATE WITH COPPER SLAG AND CEMENT ... Although copper slag is widely used in the sand blasting industry and in the ...

Research Paper EXPERIMENTAL INVESTIGATIONS ON PARTIAL REPLACEMENT OF CEMENT WITH FLY ASH IN DESIGN ... (SCMs) like fly ash (FA), blast furnace slag, silica fume, metakaolin (MK), and rice ... Research shows that adding fly ash to concrete, as a partial replacement of cement (less than 35 percent), ...

difficult for disposal. So this waste or steel slag is used for making Steel Slag Concrete. For the study of Steel Slag concrete we used M25 grade concrete. The concrete cubes as specimens of size (150mm X 150mm X 150mm) are cast for Partial replacement of steel slag .

The primary objective of the project is to increase the strength of the concrete by replacing coarse aggregate by steel slag and also 30% replacement of eco sand as fine aggregate. As of from literature steel slag is replaced for 0,15,30,45,60,75,90 % which indeed gives us .

Partial Replacement Of Sand By Steel Slag In partial replacement of sand by if it is possible to use this crusher dust in production of concrete and mortar repair . Inquiry replacement of sand in concrete with slag and mill scale

concrete, even though the vibrated concrete columns were cured exactly as SCC columns. It was found that the fire spalling mainly depended on the stress in the concrete. Byung Sik Chun et al (2005) conducted several laboratory tests and evaluated the applicability of copper slag as a partial replacement for sand.

The percentage of copper slag used for replacement of river sand are 0, 25, 50 and 75 %. Cement sand mortar joint thickness of 10 and 15 mm. Plaster ability of use of copper slag for partial replacement material for river sand. Use of copper slag as replacement material for river sand in cement concrete (0, 25, 50, 75 and 100 %)

This paper reviewed some of these industrial wastes like waste foundry sand, steel slag, copper slag, imperial smelting furnace slag (ISF slag), blast furnace slag, coal bottom ash, ferrochrome slag, palm oil clinker etc. Out of these materials, maximum number of experiments have been conducted using waste foundry sand and copper slag as fine aggregate replacement, but still more examinations are required .

In the case of concrete where fine aggregate is replaced by waste foundry sand, steel slag and palm oil clinker, slump value reduces by increasing the percentage of replacement and concrete mix in which fine aggregate substituted by copper slag and bottom ash, slump value increases by increasing the replacement ratio.

Copper slag is used in High Performance Concrete. By using the copper slag in concrete as the partial replacement for fine aggregate, sand, the workability of concrete increases and there by the strength of the concrete increases.

Partial Replacement of Copper Slag as Fine Aggregate Ambrish E1, ... concrete with partial replacement of fine aggregate by copper slag with various percentages of 0%, 10%, 15% ... The results are presented above. V. REFERENCES [1] AlJabri, K. and Makoto Hisada. "Copper slag as sand replacement for high performance concrete", Cement ...

Sustainable use of industrialwaste as partial replacement of fine aggregate for preparation of concrete – A review. ... Waste foundry sand concrete up to 20% and steel slag concrete up to 50% replacement shows similar strength like control concrete. Palm oil clinker concrete up to 10% substitution exhibits more flexural strength than ...

Effects of Copper Slag as Sand Replacement in Concrete M. V. Patil#1, *2 ... various proportions of copper slag replacement with sand of 0 to in concrete. The results ... silica fume and slag are being used into construction industry as a partial replacement to the fine

of using copper slag as a partial replacement for sand, flyash as a partial replacement for cement in addition of steel fibres in concrete. Fly ash and copper slag is a byproduct material obtained in Thermal power station and copper industries.

The slump increases with the increase in the percentage of Basic oxygen furnace slag in the concrete and reaches a maximum of 72 mm at 35% replacement of sand with basic oxygen furnace slag [79], when compared with control mix of concrete (Table 10 and .

Abstract: In the present study an investigation is made on properties of concrete by partial replacement of Cement with Ground Granulated Blast Furnace Slag (GGBS) and Fine Aggregate with Quarry Dust (QD). Ground Granulated Blast Furnace Slag is a byproduct of Iron and Steel industry which is produced in large quantities as a solid waste.

evaluate the strength of concrete made with steel slag as replacement for fine aggregates. For this present study M20 grade concrete shall be designed, Partial replacement of sand with steel slag will be made for varying percentages such as 10%, 20%, 30%, 40%, 50% by weight of sand.

the blended concrete containing different percentage of slag and steel fibre as partial replacement of cement in concrete is replaced accordinglywith the percentage of 10%, 20%, 30% and 40% by weight of slag and %,1%,%,2% by weight of steel fibre. Concrete cubes are tested at